VEL#048 - PayFacto PAX A920 SecureTablePay

VEL#048 - PayFacto PAX A920 SecureTablePay

VEL#048 - PayFacto PAX A920 SecureTablePay


Interface : PayFacto PAX A920 SecureTablePay

Compatible model : PAX A920

STP settings password : 1234

Note : You must have the STPI service installed before

 

1.      Ethernet configuration (WiFi)

If your terminal will be used for Delivery (Pay at the door), ignore the WIFI steps

a.       Connect the terminal on your 2.4ghz WiFi network

                                                               i.      Open the Android meny by swiping your finger from to bottom

                                                             ii.      Press on the WiFi icon and connect to your WiFi

                                           



1.      SecureTablePay PayFacto application setting


a.      On the main screen, press on the SecureTable PayFacto application and enter the password: posDDMM (DD : Day, MM : month – Ex : pos1103 for march 11).
This password will be asked only one time



b.       Press on the gear icon at the top right and enter the password : 1234


If you do not have the SecureTable PayFacto application, please follow these steps:

-          Press on the PAXSTORE on the main screen

-          Search for SecureTable CA on the store

-          Download the App SecureTable CA with the PayFacto logo

-          Once downloaded, it will install automatically, and the app will show up on the main screen


** When you open the SecureTable CA application for the first time, you must enter this following password : pos followed by the day and the month **
E.g : pos2411 for November 24
24 = Current date
11 = Current month 

a.       Press on advanced settings

                                                               i.      STPI Port Number : 9999

                                                             ii.      POS Type : 1

                                                           iii.      Tip : Enable ou Disable

                                                           iv.      Set the tip presets

                                                             v.      Enable Search by Table Number ( In delivery mode, it will be the delivery number on the check between () )

                                                           vi.      Enable Search by Check Number (We suggest to don't enable the check number in delivery as the delivery number will be used)

                                                          vii.      Prompt Timer : 5

                                                        viii.      Under More settings, you can set the tip % to be calculated on the sub-total or the total

                                                            ix.      You can enable the Auto Start option if you want the SecureTable app to open after a reboot

                                                ** For delivery (Pay at the door), enable the Delivery toggle **

                                                             x.      Press Save 

                                                            xi.      Under STPI IP Address, enter the IP of the POS that will run the STPI Service

** If you use SecureTable for delivery (Pay at the door) you must enter the WAN IP address (Static IP required) instead of the POS IP. If you don't have a static IP, we suggest you to install a DDNS software and use the URL instead of the IP *

                                      xii. Press on FIND STPI and you should have a success message. If not, make sure the STPI service is running on the machine.

Refer to this KB in case : KB#047EN - STPI Service installation - SecureTablePay


1.      Backoffice Configuration

a.       Electronic funds transfer

b.       Configuration / Configuration

c.     The settings at the left doesn’t matter, only set the Handheld to PosereTablePay

d.       Save
 

1.      Workstation Configuration

a.       Backoffice

b.       Point of sales control

c.       Workstation / Workstation’s setup

d.       Select the workstation that have the STPI installed

e.       Interfaces tab

f.        Check EFT

g.       Connection : Select TCP/IP

h.       Type Handheld

i.         Enter the IP address : 0.0.0.0

j.      Enter the port : 5656

k.       Save


Terminal Usage for Delivery

  1.       For delivery, you need to use a driver employee to login to the terminal
  2.       If the dispatch is activated, the driver must 'Start' with the deliveries before they are accessible from the STP
  3.       The deliveries must be closed 'Cash' to have them available to retrieve from       SecureTable
      
     


    • Related Articles

    • VEL#043 - PayFacto PAX S300

      VEL#043 - PayFacto PAX S300 Interface : PayFacto CAN Compatible terminal model : PAX S300 Admin code : The admin code is provided by PayFacto and should be included on a sheet in the package box   Terminal Setup Press on the F button       Select 3- ...
    • EFT-Q2 - Socket init failed(402) or Communication error with SecureTablePay (STP)

      EFT-Q2  Socket init failed(402) or Communication error with STP (SecureTablePay)     EFT-A2  The STP terminal is not able to fetch the tables list because of this communication error.    Causes:  Terminal is not connected to the Wifi  Terminal as ...
    • VEL#052 - PAX A920 Printers and Redirection setup

      VEL#052 - PAX A920 (VelPAX) Printers and Redirection Setup It is possible to use the PAX A920 printer to print customer's receipts directly from the terminal. (This option is not available for clients having the MEV(SRM) from Revenu Quebec) ...
    • VEL#047 - STPI Service installation - SecureTablePay

      KB#047EN - STPI Service installation - SecureTablePay Interface: Client STPI - SecureTablePay STPI Client and certificate : http://versions.velocehq.com/soft ** Please make sure the latest Java is installed:  https://www.java.com/fr/download/ **   ...
    • VEL#053 - Configure PAX A920 Integrated payment option with Veloce

      VEL#053 - Configure the PAX A920 Integrated payment option with Veloce Veloce Workstation's setup for a complete payment integration with the PAX A920 Prerequisite 1. Veloce 9.56.0 2. PayFacto's merchant account 3. Pax terminal       A920 compatible ...